Shanghai Sunland Industrial Co., Ltd is the top manufacturer of Personal Protect Equipment in China, with 20 years’experience. We are the Chinese government appointed manufacturer for government power,personal protection equipment , medical instruments,construction industry, etc. All the products get the CE, ANSI and related Industry Certificates. All our safety helmets use the top-quality raw material without any recycling material.
happy face hat
We provide exclusive customization of the products logo, using advanced printing technology and technology, not suitable for fading, solid and firm, scratch-proof and anti-smashing, and suitable for various scenes such as construction, mining, warehouse, inspection, etc. Our goal is to satisfy your needs. Demand, do your best.
Professional team work and production line which can make nice quality in short time.
The professional team provides 24 * 7 after-sales service for you, which can help you solve any problems
All UniSafe ,helmet, shells are made from premium impact resistant ABS plastic or polycarbonate. In compliance with the standards objectives, specifying ,safety helmets, is dependent on hazards involved. AS/NZS 1801:1997 classifies ,safety helmets, into three types: UniSafe Saftey ,helmets,: Type 1- General industrial ,safety helmets,.
A rivet is a permanent mechanical fastener.Before being installed, a rivet consists of a smooth cylindrical shaft with a ,head, on one end. The end opposite to ,the head, is called the tail.On installation, the rivet is placed in a punched or drilled hole, and the tail is upset, or bucked (i.e., deformed), so that it expands to about 1.5 times the original shaft diameter, holding the rivet in place.
i. As with all protective equipment, ,safety, footwear should be inspected prior to each use. ii. ,Shoes, and leggings should be checked for wear and tear at reasonable intervals. This includes looking for cracks or holes, separation of ,materials,, broken buckles or laces. iii. The soles of ,shoes, should be checked for pieces of metal or other embedded
1.6cm-thick polyurethane ,insulation, has the same ,insulation, efficiency as a 1.34m-thick concrete wall! since 2003, all polyurethane foams have been HCFC-free in the EU. the polyurethane industry employs over 360.000 people in the EU. the first polyurethane surfboard was made and used in the 1950s.
“,Insulating, layer” is a fancy way of saying “the next layer after the base layer”…which is usually a light jacket, zip up, or fleece. Again, go for wicking ,material, with warmth. Acceptable items: zipped cold gear hoodies, pullovers, light jackets and fleeces. 3.) Outer Layer (aka a Winter Jacket)
Even when wearing a helmet, always wear ,safety, glasses with side shields or goggles to prevent sparks or other debris from ,hitting, the eyes. Leather boots with 6-to-8-inch ankle coverage are the best foot protection; metatarsal guards over the ,shoe, laces can protect feet from falling objects and sparks.
Fiberglass is one of the most commonly used ,materials, for ,insulating, the home. It is an effective barrier to the passage of heat. In hot climates, it prevents heat from outside the house entering, reducing the need to use air conditioners. In colder climes, it preserves the interior heat generated by the furnace.
It is the responsibility ,of insulation, contractor to ensure adequate percautions ,against, damage and deterioration are taken during the storage ,of insulation materials,. 5.2 Installation procedure shall be subject to inspection by Owner or by his representative and any ,material,, which has been improperly installed or excessively damaged ,material, shall be removed and replace properly with ...
The depth of loft ,insulation, (in mm) equates to an R-value rating. This is a unit of thermal resistance and rates the ,insulating, properties of the ,material,. The higher the R-value, the greater the ,insulation,. A minimum R-value of 6.1 is recommended for loft floor ,insulation,, but ideally it would be up to 7.0.
The Cat Personal ,Safety, Keychain is basically a set of brass knuckles in the shape of a cat’s ,head,, with the eye holes being the grips. This one is made of plastic (they’re available in metal too) but don’t be fooled, they don’t break or even scratch easily.
The sole of the orthopedic ,shoe, designed in the way which the pressure of body on feet during walking and standing defuse the force of body all-over the foot so it brings comfortable condition without pain on special part and prevents from the tiredness and the pain of backache, the ulterior layer of the ,shoe, made by special PU ,materials, ((Polyurethane) that is anti-rubbing, Anti-petroleum ...
Hardhats shall be worn in areas where there is a potential for injury to ,the head, ... objects piercing the sole of the foot, electrical hazards, hot surfaces, and slippery surfaces. ,Safety, toe ,shoes, ... In addition, the ,insulating, grips should be kept away from sharp edges, wire clippings, and other ,materials, that could pierce the ,insulation,.